Packaged Oven
All of these ovens are designed to raise the internal temperature from ambient to the desired temperature quickly and efficiently.
You should select an oven that closely matches your heating requirements. An oven with more power than you need may not do the job as effectively or as economically as a lower-wattage oven.
Built in Timers/Microprocessor Controllers allow automatic cycling.
Overtemperature Protection ensures that an oven will not continue heating if the set point is exceeded.
Safety features protect samples against over maintain even temperature in the event of microprocessor failure.
The interior walls are made of stainless sleel. The blower and sidewall plenums are also stainless steel. Four perforated stainless shelves adjustable are included with every unif. Shelves and Racks should be conveniently arranged for your application. Removable shelves allow easier cleaning of the oven's interior.
MODEL INSIDE DIMENSION VOLUMN MAX.TEMP MOTOR ROWER POWER
SCO1615 16(H)X16(W)X16(D) 2.22Cubic foot/litres 180°c 1/2HP 380V 3PH
SCO2018 20(H)X20(W)X18(D) 4.16Cubic foot/litres 200°c 1/2HP 380V 3PH
SCO2420 28(H)X24(W)X20(D) 7.77Cubic foot/litres 200°c 1HP 380V 3PH
SCO3024 35(H)X30(W)X24(D) 14.5Cubic foot/litres 200°c 1HP 380V 3PH
SCO3226 42(H)X32(W)X26(D) 20.22Cubic foot/litres 200°c 1HP 380V 3PH
SCO3430 48(H)X34(W)X30(D) 28.33Cubic foot/litres 200°c 2HP 380V 3PH
SCO3027 60(H)X30(W)X27(D) 28.12Cubic foot/litres 200°c 2HP 380V 3PH
SCO4032 54(H)X40(W)X32(D) 40Cubic foot/litres 200°c 2HP 380V 3PH
Tuesday, September 6, 2011
Desulfurization Plaster Dryers best-selling in Africa
Desulfurization Plaster Dryers
1large capacity
2wide range of applications
3simple operation
4US $1,000 - 9,999,999 / Set
Desulfurization Plaster Dryers :
Desulfurization Plaster Dryers
, also known as gypsum dryer, is widely used in the drying of cement, mining, building materials and chemicals, grain, fertilizer production. In order to control the temperature of the dryer, in and out equipment were configured the thermocouple, and through the thermometer shows the out feed side of the dryer temperature, which provides a better basis for the control of the cylinder body temperature (usually 350-380 degrees).
1large capacity
2wide range of applications
3simple operation
4US $1,000 - 9,999,999 / Set
Desulfurization Plaster Dryers :
Desulfurization Plaster Dryers
, also known as gypsum dryer, is widely used in the drying of cement, mining, building materials and chemicals, grain, fertilizer production. In order to control the temperature of the dryer, in and out equipment were configured the thermocouple, and through the thermometer shows the out feed side of the dryer temperature, which provides a better basis for the control of the cylinder body temperature (usually 350-380 degrees).
works reliably coal slime rotary dryer
1.High efficiency
2.Easy operation and maintenance.
3.Simple and reliable structure rotary dryer.
Rotary dryer main application:
The indirect heat transfer dryer made by our company can be used in building materials, metallurgy, chemical industry, cement plant for drying of limestone slag, coal powder, slag, clay stone.
Rotary dryer usage:
This series drier is used for drying materials with humidity or granularity in the industries of mineral dressing, building material, metallurgy and chemical. Rotating dryer can be used for drying many kinds of materials and with convenient and reliable operation; therefore, it has been widely used.
Rotary Dryer features:
Widely used in drying different materials!
reasonable structure,high efficiency
low energy consumption
Technical parameter list
Pro duct specifications
Capacity
Motor
Reducer
SizeLength × width × height
(mm)
Weight (T)
Volume(M
3
Speed (r/min)
Gradient%
Model
Power (Kw )
Model
Φ1×10M
7.85
6.73
3-5
Y132M2-6
5.5
ZL350--25
10000×1876×2069
7.5
Φ1.2×6M
6.8
5.8
3-5
Y132M2-6
5.5
ZL359--25
6000×2159×2475
7.97
Φ1.2×8M
9.1
5.8
3-5
Y132M2-6
5.5
ZL350--25
8000×2159×2475
8.75
Φ1.2×10M
11.31
5.8
3-5
Y160M-6
7.5
ZL350--25
10000×2159×2475
9.52
Φ1.2×12M
13.31
5.8
3-5
Y160L-6
11
ZQ500--31.5
12000×2159×2475
13.1
Φ1.5×8M
14.14
4.8
3-5
Y160L-6
11
ZQ650--2F
ZQ650--1F
8000×2655×2895
15.74
Φ1.5×10M
17.67
4.8
3-5
Y160L-6
11
ZQ650--2F
ZQ650--1F
10000& times;2655×2895
17.93
Φ1.5×12M
21.2
4.8
3-5
180L-6
15
ZQ650--31.5
12000×2655×2895
22.3
Φ1.5×14M
24.9
4.8
3-5
180L-6
15
ZQ650--31.5
14000×2655×2895
25.1
2.Easy operation and maintenance.
3.Simple and reliable structure rotary dryer.
Rotary dryer main application:
The indirect heat transfer dryer made by our company can be used in building materials, metallurgy, chemical industry, cement plant for drying of limestone slag, coal powder, slag, clay stone.
Rotary dryer usage:
This series drier is used for drying materials with humidity or granularity in the industries of mineral dressing, building material, metallurgy and chemical. Rotating dryer can be used for drying many kinds of materials and with convenient and reliable operation; therefore, it has been widely used.
Rotary Dryer features:
Widely used in drying different materials!
reasonable structure,high efficiency
low energy consumption
Technical parameter list
Pro duct specifications
Capacity
Motor
Reducer
SizeLength × width × height
(mm)
Weight (T)
Volume(M
3
Speed (r/min)
Gradient%
Model
Power (Kw )
Model
Φ1×10M
7.85
6.73
3-5
Y132M2-6
5.5
ZL350--25
10000×1876×2069
7.5
Φ1.2×6M
6.8
5.8
3-5
Y132M2-6
5.5
ZL359--25
6000×2159×2475
7.97
Φ1.2×8M
9.1
5.8
3-5
Y132M2-6
5.5
ZL350--25
8000×2159×2475
8.75
Φ1.2×10M
11.31
5.8
3-5
Y160M-6
7.5
ZL350--25
10000×2159×2475
9.52
Φ1.2×12M
13.31
5.8
3-5
Y160L-6
11
ZQ500--31.5
12000×2159×2475
13.1
Φ1.5×8M
14.14
4.8
3-5
Y160L-6
11
ZQ650--2F
ZQ650--1F
8000×2655×2895
15.74
Φ1.5×10M
17.67
4.8
3-5
Y160L-6
11
ZQ650--2F
ZQ650--1F
10000& times;2655×2895
17.93
Φ1.5×12M
21.2
4.8
3-5
180L-6
15
ZQ650--31.5
12000×2655×2895
22.3
Φ1.5×14M
24.9
4.8
3-5
180L-6
15
ZQ650--31.5
14000×2655×2895
25.1
Centrifugal Spray Dryer
1.Centrifugal Spray Dryer
2.momentary dry,simple opetation,easy control
3.drying liquid,emulsion,suspension,paste,polymer
Features:
spray drier has high drying speed, usually,it just needs 5-15 seconds. It has feature of momentary dry.
Because raw material can be dried in very time,therefore, it is particularly suiable for drying heat sensitive raw materials. It can keep color, flavor in good quality. the purity quotient of finished products is high and quality is really good. The operation is simple and production procee is simplified. Its regulation and control is very convenient. It is easy to realize continuous production.
The distribution, fluidity and solubility of product are good.
Principle of work:
Air is turned into hot air through air filter and heater and enters into hot air distributor at the top o f drier and then enters into drier uniformly with the state of helix. At the same time liquid of raw material is sent to centrifugal atomizer at the top of dry chamber by pump through filter, liquid of raw material jet out and tunr into small drops. Hot air and liquid of raw material contact fully. The moisture vaporize rapidly and raw material is dried into finished product of powder state in a short time. The finished product is discharged through cyclone seperator from the bottom of drier. The exhausted air is discharged through fan.
2.momentary dry,simple opetation,easy control
3.drying liquid,emulsion,suspension,paste,polymer
Features:
spray drier has high drying speed, usually,it just needs 5-15 seconds. It has feature of momentary dry.
Because raw material can be dried in very time,therefore, it is particularly suiable for drying heat sensitive raw materials. It can keep color, flavor in good quality. the purity quotient of finished products is high and quality is really good. The operation is simple and production procee is simplified. Its regulation and control is very convenient. It is easy to realize continuous production.
The distribution, fluidity and solubility of product are good.
Principle of work:
Air is turned into hot air through air filter and heater and enters into hot air distributor at the top o f drier and then enters into drier uniformly with the state of helix. At the same time liquid of raw material is sent to centrifugal atomizer at the top of dry chamber by pump through filter, liquid of raw material jet out and tunr into small drops. Hot air and liquid of raw material contact fully. The moisture vaporize rapidly and raw material is dried into finished product of powder state in a short time. The finished product is discharged through cyclone seperator from the bottom of drier. The exhausted air is discharged through fan.
High quality Air current drier
1.High quality Air current drier
2.High efficiency drying capacity
3.Low energy consumption
4.Easy operation, maintenance
Air current drier
Description of
Air current drier:
Drier is professionally designed for drying wood sawdust
For raw materials with heavy humidity which is above 12%
Need to install a drier before further processing
Can reduce the humidity of wood materials below 12% per time
Cost of this air current drier is much lower than rotary drier
Professionally designed for drying different kinds of wood sawdust
Low cost, low consumption, high capacity, easy operation and maintenance, and more
Round places of pipes can be changed to any angle which can save space and solve plant dimension limitation
HGJ-I and HGJ-II type drier (with one stove):
Suitable to process materials which moi sture content is between 20 to 25%
Can reduce the MS to 8 to 12% one drying time
Regarding HGJ-III (with two stoves):
Suitable to process materials which moisture content is between 35 to 50%
Can reduce the humidity to 8 to 12% one drying time
Can reduce approximately 30% for one drying time
Humidity of materials is lower than 35%, the capacity will be increased with less of fuel
Can be adjusted to any angle of 360° according to operation request
Clients can change the angle of drier s base on the production field
Technical Specification of Air current drier:
Model
Diameter (mm)
Water evaporation(kg/h)
Power(kw)
Area(m2)
WGQ25
250
30~80
13
15
WGQ30
300
70~150
16.5
20
WGQ35
350
100~200
22
25
WGQ40
400
120~250
29
25
WGQ50
500
200~400
50.2
30
WGQ60
600
300~600
68.2
40
2.High efficiency drying capacity
3.Low energy consumption
4.Easy operation, maintenance
Air current drier
Description of
Air current drier:
Drier is professionally designed for drying wood sawdust
For raw materials with heavy humidity which is above 12%
Need to install a drier before further processing
Can reduce the humidity of wood materials below 12% per time
Cost of this air current drier is much lower than rotary drier
Professionally designed for drying different kinds of wood sawdust
Low cost, low consumption, high capacity, easy operation and maintenance, and more
Round places of pipes can be changed to any angle which can save space and solve plant dimension limitation
HGJ-I and HGJ-II type drier (with one stove):
Suitable to process materials which moi sture content is between 20 to 25%
Can reduce the MS to 8 to 12% one drying time
Regarding HGJ-III (with two stoves):
Suitable to process materials which moisture content is between 35 to 50%
Can reduce the humidity to 8 to 12% one drying time
Can reduce approximately 30% for one drying time
Humidity of materials is lower than 35%, the capacity will be increased with less of fuel
Can be adjusted to any angle of 360° according to operation request
Clients can change the angle of drier s base on the production field
Technical Specification of Air current drier:
Model
Diameter (mm)
Water evaporation(kg/h)
Power(kw)
Area(m2)
WGQ25
250
30~80
13
15
WGQ30
300
70~150
16.5
20
WGQ35
350
100~200
22
25
WGQ40
400
120~250
29
25
WGQ50
500
200~400
50.2
30
WGQ60
600
300~600
68.2
40
brewer's grains dryer machine
drying machine
1.High thermal efficiency
2.Energy saving and large capacity
3.Little engineering investment
4.Convenient
o
drying machine
Rotary dryer is widely used in building materials, metallurgy, chemicals, coal, sand and fertilizer industrials to dry the materials with certain humidity or granularity. It can dry various different materials it is easy to operation. That is why this machine is so welcomed by customers.
Specifications of drying machine
1) Widely used in building material, metallurgy, chemical industry, cement to dry
the slag, limestone, coal powder and clay
2) It mainly consists of lifting blade, transmission device, supporting device and
seal ring
3) Simple structure, polished, high capacity, low consumption, convenient for transportationTechnical parameters
Operation Principle of drying machine
The raw material plate which is arranged reasonably with changeable angles in order, throws moisture materials into the rotary cylinder. Then water will be separated from the materials by hot air-flow and changed into vapour to be discharged into the atmosphere. Then the materials would be dried. Rotary dryer is used to dry slag, clay, limestone; It is mainly used for cement, chemical, metallurgical, building materials industries. Its advantages are as follows: high dry capacity, smooth rotation, and low energy consumption, easy operation, high output and so on.
Technical parameters of drying machine
Model(m)
Capacity(T/H)
Main motor
Reducer
Weight(T)
Power(KW)
Model
Model
Speed ratio
Φ1.2×10m
2.5
7.5
Y160M-R
3
ZL50-16-I
13.5
Φ1.5×12m
3.3-4.9
10
Y160L-6-B
3
JZQ500-3-2F
18.9
Φ1.5×15m
4-6
18.5
Y200L
1
-6
JZQ500-3-2F
21
Φ1.8×12m
4-6
11
Y160L-6
ZQ50-16-2-2
16.46
22.83
Φ2.2×12m
7-12
18.5
Y200L
7
-6
JZQ650-3
31.5
37.6
Φ2.2×14m
7-12
18.5
Y200L
7
-6
JZQ650-3
31.5
40
Φ2.2×16m
12
30
Y225M-6
JZQ750-3
31.5
45
Φ2.4×14m
12
30
Y250M-6
JZQ750-3
31.5
51
Φ2.4×18m
10-13
37
Y250M-6
ZL85-13-I
27.16
54
Φ2.4×20m
10-14
37
Y250N-6
ZL85-13-I
27.16
54.14
Φ3×20m
25
55
Y250M-4
ZL100-16-I
41.52
78
Φ3×25m
32-36
75
YR280M-4
ZL100-16-I
41.52
104.9
1.High thermal efficiency
2.Energy saving and large capacity
3.Little engineering investment
4.Convenient
o
drying machine
Rotary dryer is widely used in building materials, metallurgy, chemicals, coal, sand and fertilizer industrials to dry the materials with certain humidity or granularity. It can dry various different materials it is easy to operation. That is why this machine is so welcomed by customers.
Specifications of drying machine
1) Widely used in building material, metallurgy, chemical industry, cement to dry
the slag, limestone, coal powder and clay
2) It mainly consists of lifting blade, transmission device, supporting device and
seal ring
3) Simple structure, polished, high capacity, low consumption, convenient for transportationTechnical parameters
Operation Principle of drying machine
The raw material plate which is arranged reasonably with changeable angles in order, throws moisture materials into the rotary cylinder. Then water will be separated from the materials by hot air-flow and changed into vapour to be discharged into the atmosphere. Then the materials would be dried. Rotary dryer is used to dry slag, clay, limestone; It is mainly used for cement, chemical, metallurgical, building materials industries. Its advantages are as follows: high dry capacity, smooth rotation, and low energy consumption, easy operation, high output and so on.
Technical parameters of drying machine
Model(m)
Capacity(T/H)
Main motor
Reducer
Weight(T)
Power(KW)
Model
Model
Speed ratio
Φ1.2×10m
2.5
7.5
Y160M-R
3
ZL50-16-I
13.5
Φ1.5×12m
3.3-4.9
10
Y160L-6-B
3
JZQ500-3-2F
18.9
Φ1.5×15m
4-6
18.5
Y200L
1
-6
JZQ500-3-2F
21
Φ1.8×12m
4-6
11
Y160L-6
ZQ50-16-2-2
16.46
22.83
Φ2.2×12m
7-12
18.5
Y200L
7
-6
JZQ650-3
31.5
37.6
Φ2.2×14m
7-12
18.5
Y200L
7
-6
JZQ650-3
31.5
40
Φ2.2×16m
12
30
Y225M-6
JZQ750-3
31.5
45
Φ2.4×14m
12
30
Y250M-6
JZQ750-3
31.5
51
Φ2.4×18m
10-13
37
Y250M-6
ZL85-13-I
27.16
54
Φ2.4×20m
10-14
37
Y250N-6
ZL85-13-I
27.16
54.14
Φ3×20m
25
55
Y250M-4
ZL100-16-I
41.52
78
Φ3×25m
32-36
75
YR280M-4
ZL100-16-I
41.52
104.9
Air Dryer(High Temperature)
High inlet temperature, air-cooled, low working pressure (high working pressure)
Specifications:
1) Capacity: 0.5 - 300Nm
3
/min
2) Inlet temperature: ≤80°C
3) Working pressure: 1.0MPa(normally)
4) Dew point: 2-10°C
5) Voltage: 380V/3PH/50Hz; 220V/1PH/50Hz
6) Coolant: R-22, R407c, R134a
7) Cooling method: air-cooled
8) custom-tailor by custom design or requirement
Specifications:
1) Capacity: 0.5 - 300Nm
3
/min
2) Inlet temperature: ≤80°C
3) Working pressure: 1.0MPa(normally)
4) Dew point: 2-10°C
5) Voltage: 380V/3PH/50Hz; 220V/1PH/50Hz
6) Coolant: R-22, R407c, R134a
7) Cooling method: air-cooled
8) custom-tailor by custom design or requirement
Subscribe to:
Comments (Atom)